Plates
Hot rolled and quenched plate, cut to size, profile cut or supplied full size.
44 grades · Plates
[ 01 ]
Alloy Steel
AISI 4140 / 42CrMo4
Ex-stock DubaiThe benchmark chromium-molybdenum through-hardening engineering steel. Excellent combination of strength, toughness and machinability in the quenched and tempered condition.
SA387 Grade 11 Class 2
Mill indent1.25Cr-0.5Mo-Si pressure vessel plate. The silicon addition improves oxidation resistance, making Grade 11 the common choice for hot wall vessels and hydrogen service up to around 550 C where full 2.25Cr strength is not required.
SA387 Grade 12 Class 2
Mill indent1Cr-0.5Mo pressure vessel plate. The economical Cr-Mo grade for moderate temperature pressure parts, widely used for separator and drum shells where creep and hydrogen resistance are needed but the duty is below the 2.25Cr range.
SA387 Grade 22 Class 2
Mill indent2.25Cr-1Mo pressure vessel plate — the refinery standard for hydroprocessing. The higher chromium and molybdenum push the Nelson curve limit well above Grade 11, which is why reactors, separators and hot wall equipment in hydrogen service specify it.
SA387 Grade 5 Class 2
Mill indent5Cr-0.5Mo plate. The chromium level lifts resistance to sulphidic corrosion and high temperature oxidation, so Grade 5 is specified for crude and vacuum unit hot sections where naphthenic and sulphur attack dominate.
SA387 Grade 9 Class 2
Mill indent9Cr-1Mo plate for high temperature service. Used where sulphidic corrosion resistance and creep strength have to be carried above the 5Cr range, typically in refinery heaters and transfer line equipment.
SA387 Grade 91 Class 2
Mill indentModified 9Cr-1Mo-V (Grade 91) plate. Vanadium and niobium micro-alloying gives roughly twice the creep rupture strength of Grade 22 at 550 - 600 C, enabling thinner, lighter pressure parts in supercritical steam and high temperature process plant. Heat treatment and PWHT control are critical and are recorded on the certificate.
[ 02 ]
Armor & Ballistic Steel
Armox 500T
SSABMill indentThe most widely used protection plate worldwide. Balances ballistic performance with the weldability and formability a fabricator needs to build complete armoured structures.
Armox 600T
SSABMill indentHigh hardness protection plate delivering the same protection level at reduced weight, or a higher threat level at the same weight, compared with 500 HBW armour.
[ 03 ]
Carbon Steel Plates
S355J2+N Steel Plates
Ex-stock DubaiNormalised structural plate with guaranteed 27 J impact energy at -20 C. The J2+N condition gives consistent toughness and flatness through thick sections, which is why it is specified for welded structures, crane and bridge work and heavy fabrication in the Gulf.
S355J2W+N / Corten Steel Plates
Mill indentWeathering structural plate. Copper, chromium and nickel additions let a dense, adherent oxide patina form that seals the surface, so the structure can be left unpainted and the maintenance coating cycle disappears.
SA516 Grade 60 Plates
Mill indentCarbon pressure vessel plate for moderate and lower temperature service. The lower carbon of Grade 60 gives better formability and weldability than Grade 70, which suits cold-formed heads, thin shells and plant where notch toughness matters more than tensile strength.
SA516 Grade 70 Plates
Ex-stock DubaiThe default carbon pressure vessel plate. Grade 70 carries the highest tensile of the SA516 family, and for sour service it is supplied with controlled sulphur, calcium treatment and HIC / SSC testing so wet H2S equipment can be built from a qualified plate rather than an upgrade alloy.
[ 04 ]
Cupro Nickel
Cupro Nickel 90/10 Seamless Pipes
Mill indentThe default seawater alloy. 90% copper with 10% nickel and a controlled iron addition builds a protective cuprous oxide film in seawater, and the inherent copper toxicity stops macrofouling — barnacles and mussels do not settle, so cooling lines stay clean without chlorination. Specified for ship and platform seawater systems, firewater ring mains and condenser tubing where the velocity stays below about 3.5 m/s.
Cupro Nickel 70/30 Seamless Pipes
Mill indentThe higher-duty cupro nickel. Tripling the nickel to 30% raises strength, erosion-corrosion resistance and the allowable seawater velocity to around 4.5 m/s, and lifts the service temperature well above 90/10. It is the grade for pump and valve-adjacent piping, hot brine and MSF desalination heat recovery, and any line where turbulence or sand loading would strip the film off 90/10.
Cupro Nickel 66/30/2/2 (C71640)
Project supplyThe desalination variant of 70/30. Raising iron and manganese to about 2% each stabilises the protective film under high velocity, sand-laden and partly deaerated brine, which is exactly the duty inside MSF evaporator heat recovery and reject sections. Where 70/30 tubes thin at the inlet ends, C71640 holds.
[ 05 ]
Duplex & Super Duplex
Duplex 2205
Ex-stock DubaiThe most widely used duplex grade. Roughly double the yield strength of 316L, allowing thinner and lighter sections while delivering far better chloride stress corrosion cracking resistance.
Super Duplex 2507
Mill indentSuper duplex with PREN above 40 for the most aggressive seawater and sour service. S32760 (Zeron 100) adds tungsten and copper for enhanced acid resistance.
[ 06 ]
High Strength Steel
S690QL
Ex-stock DubaiQuenched and tempered structural steel with 690 MPa minimum yield. Allows dramatic weight reduction in load bearing structures against conventional S355.
S960QL
Mill indentUltra high strength quenched and tempered plate for the most weight-critical lifting and mobile equipment structures.
S1100QL
Mill indentThe highest yield strength structural plate in commercial supply, used where every kilogram of structural weight carries a payload penalty.
[ 07 ]
Nickel Alloys
Inconel 625
Mill indentNickel-chromium-molybdenum alloy strengthened by niobium. Exceptional strength and corrosion resistance from cryogenic temperatures to 980 C without heat treatment.
Inconel 600
Mill indentSolid solution nickel-chromium-iron alloy with high resistance to oxidation, carburisation and chloride ion stress corrosion cracking at elevated temperature.
Monel 400
Mill indentNickel-copper alloy with outstanding resistance to flowing seawater, hydrofluoric acid and alkalis, and total immunity to chloride stress corrosion cracking.
Hastelloy C276
Mill indentNickel-molybdenum-chromium alloy with tungsten, regarded as the most universally corrosion resistant alloy available for both oxidising and reducing media.
Alloy 800 (Incoloy 800)
Mill indentIron-nickel-chromium alloy for high temperature strength with oxidation and carburisation resistance. The 32Ni-21Cr balance resists chloride stress corrosion cracking that austenitic stainless suffers, which is why it is standard for process heater and reformer tubing.
Alloy 800HT (Incoloy 800HT)
Mill indentThe creep-optimised version of Alloy 800. Controlled carbon plus a combined aluminium and titanium window of 0.85 - 1.20% gives far better creep rupture strength above 600 C, so 800HT is the grade for the hottest reformer and pigtail service rather than plain 800.
Alloy 825 (Incoloy 825)
Mill indentNickel-iron-chromium with molybdenum, copper and titanium. The combination handles both reducing and oxidising acids and resists chloride stress corrosion cracking and sour well fluids, making 825 the standard CRA for sour service tubulars, cladding and acid plant.
Alloy 617
Mill indentNickel-chromium-cobalt-molybdenum alloy for the extreme end of high temperature service. Solid solution strengthening keeps useful creep strength to 1100 C while the chromium and aluminium give oxidation resistance, so 617 is used where 800HT and stainless are long past their limit.
Alloy 740H
Project supplyPrecipitation-hardened nickel alloy developed for advanced ultra-supercritical boilers. Gamma-prime strengthening plus about 25% chromium holds creep rupture strength and coal-ash corrosion resistance at 750 C and above, which is beyond what 617 can carry in thick section steam headers.
[ 08 ]
Stainless Steel
304 / 304L
Ex-stock DubaiThe workhorse austenitic stainless steel. 304L's lower carbon content prevents carbide precipitation during welding, making it the default choice for welded fabrications that cannot be post-weld annealed.
316 / 316L
Ex-stock DubaiMolybdenum-bearing austenitic stainless steel. The 2-3% Mo addition transforms pitting resistance in chloride-bearing media, making 316L the baseline grade for marine and chemical service in the Gulf.
321 / 347
Ex-stock DubaiTitanium and niobium stabilised austenitic grades. The stabilising addition ties up carbon so the steel resists intergranular corrosion after prolonged exposure in the 425-815 C sensitisation range.
904L
Mill indentHigh alloy austenitic grade with 4-5% molybdenum and copper, bridging the gap between 316L and nickel alloys for sulphuric and phosphoric acid service.
310S Stainless Steel
Mill indentThe high-temperature austenitic. 25Cr-20Ni gives scaling resistance to around 1035 C in continuous service, so 310S is the grade for furnace internals, radiant tubes and anything that lives in flue gas rather than in water.
317L Stainless Steel
Mill indentA molybdenum-up step on 316L. Raising Mo to 3 - 4% lifts PREN to around 30, which buys real margin against pitting and crevice attack in pulp, scrubber and chloride service where 316L is borderline but duplex is more than the duty needs.
316Ti Stainless Steel
Mill indentTitanium-stabilised 316. The titanium ties up carbon so the steel keeps its intergranular corrosion resistance after long exposure in the 425 - 815 C sensitisation range, and it holds higher creep strength than 316L in hot service.
[ 09 ]
Titanium
Titanium Grade 2
Mill indentCommercially pure titanium, the industry workhorse. Fully resistant to seawater and oxidising chlorides with excellent formability and weldability.
Titanium Grade 5 (Ti-6Al-4V)
Mill indentThe most widely used titanium alloy, accounting for the majority of all titanium consumption. Roughly three times the strength of commercially pure titanium at the same density.
[ 10 ]
UHMW-PE
UHMW PE1000
OrbilanEx-stock DubaiStandard ultra high molecular weight polyethylene liner sheet. The lowest coefficient of friction of any engineering polymer combined with outstanding impact absorption.
UHMW PE8000
OrbilanMill indentEnhanced UHMW-PE with a higher molecular weight delivering around 30% better abrasion performance than standard PE1000 for the most demanding liner duties.
[ 11 ]
Wear Resistant Steel
Hardox 450
SSABEx-stock DubaiThe most versatile abrasion resistant plate in the range. 450 HBW delivers roughly 2.5 times the service life of mild steel while remaining straightforward to bend, cut and weld in a normal workshop.
Hardox 500
SSABEx-stock DubaiHigher hardness plate for severe sliding abrasion where 450 HBW wears out too quickly, while retaining good workshop formability.
Hardox 600
SSABEx-stock DubaiThe hardest abrasion resistant plate in general production, reserved for extreme sliding wear where part replacement downtime dominates cost.