Fittings

Butt weld and forged fittings: elbows, tees, reducers, caps and couplings.

36 grades · Fittings

[ 01 ]

Alloy Steel

View all
SA387 Grade 11 Class 2

SA387 Grade 11 Class 2

Mill indent
ASTM / ASME A387 / SA387 Grade 11 Class 2EN 13CrMoSi5-5 / 1.7336

1.25Cr-0.5Mo-Si pressure vessel plate. The silicon addition improves oxidation resistance, making Grade 11 the common choice for hot wall vessels and hydrogen service up to around 550 C where full 2.25Cr strength is not required.

3 forms available
SA387 Grade 12 Class 2

SA387 Grade 12 Class 2

Mill indent
ASTM / ASME A387 / SA387 Grade 12 Class 2EN 13CrMo4-5 / 1.7335

1Cr-0.5Mo pressure vessel plate. The economical Cr-Mo grade for moderate temperature pressure parts, widely used for separator and drum shells where creep and hydrogen resistance are needed but the duty is below the 2.25Cr range.

3 forms available
SA387 Grade 22 Class 2

SA387 Grade 22 Class 2

Mill indent
ASTM / ASME A387 / SA387 Grade 22 Class 2EN 10CrMo9-10 / 1.7380

2.25Cr-1Mo pressure vessel plate — the refinery standard for hydroprocessing. The higher chromium and molybdenum push the Nelson curve limit well above Grade 11, which is why reactors, separators and hot wall equipment in hydrogen service specify it.

3 forms available
SA387 Grade 5 Class 2

SA387 Grade 5 Class 2

Mill indent
ASTM / ASME A387 / SA387 Grade 5 Class 2EN X12CrMo5 / 1.7362

5Cr-0.5Mo plate. The chromium level lifts resistance to sulphidic corrosion and high temperature oxidation, so Grade 5 is specified for crude and vacuum unit hot sections where naphthenic and sulphur attack dominate.

3 forms available
SA387 Grade 9 Class 2

SA387 Grade 9 Class 2

Mill indent
ASTM / ASME A387 / SA387 Grade 9 Class 2EN X11CrMo9-1 / 1.7386

9Cr-1Mo plate for high temperature service. Used where sulphidic corrosion resistance and creep strength have to be carried above the 5Cr range, typically in refinery heaters and transfer line equipment.

3 forms available
SA387 Grade 91 Class 2

SA387 Grade 91 Class 2

Mill indent
ASTM / ASME A387 / SA387 Grade 91 Class 2EN X10CrMoVNb9-1 / 1.4903

Modified 9Cr-1Mo-V (Grade 91) plate. Vanadium and niobium micro-alloying gives roughly twice the creep rupture strength of Grade 22 at 550 - 600 C, enabling thinner, lighter pressure parts in supercritical steam and high temperature process plant. Heat treatment and PWHT control are critical and are recorded on the certificate.

3 forms available
A335 P11 Seamless Pipe

A335 P11 Seamless Pipe

Mill indent
ASTM / ASME A335 / SA335 Grade P11EN 13CrMoSi5-5 / 1.7336

1.25Cr-0.5Mo seamless pipe. The matching pipe grade to SA387 Grade 11, used for moderate temperature steam and process lines where plain carbon steel loses strength and oxidation resistance.

3 forms available
A335 P12 Seamless Pipe

A335 P12 Seamless Pipe

Mill indent
ASTM / ASME A335 / SA335 Grade P12EN 13CrMo4-5 / 1.7335

1Cr-0.5Mo seamless pipe. The economical Cr-Mo pipe grade for boiler feed, steam and hot process service up to around 540 C, and the usual partner to SA387 Grade 12 plate.

3 forms available
A335 P22 Seamless Pipe

A335 P22 Seamless Pipe

Mill indent
ASTM / ASME A335 / SA335 Grade P22EN 10CrMo9-10 / 1.7380

2.25Cr-1Mo seamless pipe — the main steam and hot reheat standard. P22 carries creep strength and hydrogen resistance across refinery hot wall piping, superheater headers and heater coils, and is the pipe most often paired with SA387 Grade 22 vessels.

3 forms available
A335 P5 Seamless Pipe

A335 P5 Seamless Pipe

Mill indent
ASTM / ASME A335 / SA335 Grade P5EN X12CrMo5 / 1.7362

5Cr-0.5Mo seamless pipe for sulphidic and naphthenic service. Specified on crude and vacuum transfer lines and heater passes where sulphur attack, not pressure, sets the material.

3 forms available
A335 P9 Seamless Pipe

A335 P9 Seamless Pipe

Mill indent
ASTM / ASME A335 / SA335 Grade P9EN X11CrMo9-1 / 1.7386

9Cr-1Mo seamless pipe. Higher chromium for oxidation and sulphidic corrosion resistance in refinery heater coils and high temperature transfer lines.

3 forms available
A335 P91 Seamless Pipe

A335 P91 Seamless Pipe

Mill indent
ASTM / ASME A335 / SA335 Grade P91EN X10CrMoVNb9-1 / 1.4903

Modified 9Cr-1Mo-V (P91) seamless pipe for supercritical steam. The creep strength allows a much thinner wall than P22 at 580 - 600 C, cutting weight and thermal fatigue on main steam and hot reheat lines. Hardness after PWHT is reported on every length.

3 forms available

[ 02 ]

Cupro Nickel

View all

[ 04 ]

Nickel Alloys

View all
Inconel 625

Inconel 625

Mill indent
UNS N06625EN 2.4856

Nickel-chromium-molybdenum alloy strengthened by niobium. Exceptional strength and corrosion resistance from cryogenic temperatures to 980 C without heat treatment.

5 forms available
Inconel 600

Inconel 600

Mill indent
UNS N06600EN 2.4816

Solid solution nickel-chromium-iron alloy with high resistance to oxidation, carburisation and chloride ion stress corrosion cracking at elevated temperature.

5 forms available
Monel 400

Monel 400

Mill indent
UNS N04400EN 2.4360

Nickel-copper alloy with outstanding resistance to flowing seawater, hydrofluoric acid and alkalis, and total immunity to chloride stress corrosion cracking.

5 forms available
Hastelloy C276

Hastelloy C276

Mill indent
UNS N10276EN 2.4819

Nickel-molybdenum-chromium alloy with tungsten, regarded as the most universally corrosion resistant alloy available for both oxidising and reducing media.

5 forms available
Alloy 800 (Incoloy 800)

Alloy 800 (Incoloy 800)

Mill indent
UNS N08800EN 1.4876 / X10NiCrAlTi32-21

Iron-nickel-chromium alloy for high temperature strength with oxidation and carburisation resistance. The 32Ni-21Cr balance resists chloride stress corrosion cracking that austenitic stainless suffers, which is why it is standard for process heater and reformer tubing.

5 forms available
Alloy 800HT (Incoloy 800HT)

Alloy 800HT (Incoloy 800HT)

Mill indent
UNS N08811EN 1.4959 / X8NiCrAlTi32-21

The creep-optimised version of Alloy 800. Controlled carbon plus a combined aluminium and titanium window of 0.85 - 1.20% gives far better creep rupture strength above 600 C, so 800HT is the grade for the hottest reformer and pigtail service rather than plain 800.

5 forms available
Alloy 825 (Incoloy 825)

Alloy 825 (Incoloy 825)

Mill indent
UNS N08825EN 2.4858 / NiCr21Mo

Nickel-iron-chromium with molybdenum, copper and titanium. The combination handles both reducing and oxidising acids and resists chloride stress corrosion cracking and sour well fluids, making 825 the standard CRA for sour service tubulars, cladding and acid plant.

5 forms available
Alloy 617

Alloy 617

Mill indent
UNS N06617EN 2.4663 / NiCr23Co12Mo

Nickel-chromium-cobalt-molybdenum alloy for the extreme end of high temperature service. Solid solution strengthening keeps useful creep strength to 1100 C while the chromium and aluminium give oxidation resistance, so 617 is used where 800HT and stainless are long past their limit.

5 forms available

[ 05 ]

OCTG & Line Pipe

View all

[ 06 ]

Stainless Steel

View all
304 / 304L

304 / 304L

Ex-stock Dubai
UNS S30400 / S30403EN 1.4301 / 1.4307

The workhorse austenitic stainless steel. 304L's lower carbon content prevents carbide precipitation during welding, making it the default choice for welded fabrications that cannot be post-weld annealed.

6 forms available
316 / 316L

316 / 316L

Ex-stock Dubai
UNS S31600 / S31603EN 1.4401 / 1.4404

Molybdenum-bearing austenitic stainless steel. The 2-3% Mo addition transforms pitting resistance in chloride-bearing media, making 316L the baseline grade for marine and chemical service in the Gulf.

6 forms available
321 / 347

321 / 347

Ex-stock Dubai
UNS S32100 / S34700EN 1.4541 / 1.4550

Titanium and niobium stabilised austenitic grades. The stabilising addition ties up carbon so the steel resists intergranular corrosion after prolonged exposure in the 425-815 C sensitisation range.

5 forms available
904L

904L

Mill indent
UNS N08904EN 1.4539

High alloy austenitic grade with 4-5% molybdenum and copper, bridging the gap between 316L and nickel alloys for sulphuric and phosphoric acid service.

5 forms available
310S Stainless Steel

310S Stainless Steel

Mill indent
UNS S31008EN 1.4845 / X8CrNi25-21

The high-temperature austenitic. 25Cr-20Ni gives scaling resistance to around 1035 C in continuous service, so 310S is the grade for furnace internals, radiant tubes and anything that lives in flue gas rather than in water.

6 forms available
317L Stainless Steel

317L Stainless Steel

Mill indent
UNS S31703EN 1.4438 / X2CrNiMo18-15-4

A molybdenum-up step on 316L. Raising Mo to 3 - 4% lifts PREN to around 30, which buys real margin against pitting and crevice attack in pulp, scrubber and chloride service where 316L is borderline but duplex is more than the duty needs.

6 forms available
316Ti Stainless Steel

316Ti Stainless Steel

Mill indent
UNS S31635EN 1.4571 / X6CrNiMoTi17-12-2

Titanium-stabilised 316. The titanium ties up carbon so the steel keeps its intergranular corrosion resistance after long exposure in the 425 - 815 C sensitisation range, and it holds higher creep strength than 316L in hot service.

6 forms available