محرك البحث عن الدرجات

الفولاذ الهندسي الكروم-الموليبدينوم من خلال التقسية. يجمع بشكل ممتاز بين القوة والمتانة وقابلية التشغيل الآلي في الحالة المروية والمقساة.

1.25Cr-0.5Mo-Si pressure vessel plate. The silicon addition improves oxidation resistance, making Grade 11 the common choice for hot wall vessels and hydrogen service up to around 550 C where full 2.25Cr strength is not required.

1Cr-0.5Mo pressure vessel plate. The economical Cr-Mo grade for moderate temperature pressure parts, widely used for separator and drum shells where creep and hydrogen resistance are needed but the duty is below the 2.25Cr range.

2.25Cr-1Mo pressure vessel plate — the refinery standard for hydroprocessing. The higher chromium and molybdenum push the Nelson curve limit well above Grade 11, which is why reactors, separators and hot wall equipment in hydrogen service specify it.

5Cr-0.5Mo plate. The chromium level lifts resistance to sulphidic corrosion and high temperature oxidation, so Grade 5 is specified for crude and vacuum unit hot sections where naphthenic and sulphur attack dominate.

9Cr-1Mo plate for high temperature service. Used where sulphidic corrosion resistance and creep strength have to be carried above the 5Cr range, typically in refinery heaters and transfer line equipment.

Modified 9Cr-1Mo-V (Grade 91) plate. Vanadium and niobium micro-alloying gives roughly twice the creep rupture strength of Grade 22 at 550 - 600 C, enabling thinner, lighter pressure parts in supercritical steam and high temperature process plant. Heat treatment and PWHT control are critical and are recorded on the certificate.

1.25Cr-0.5Mo seamless pipe. The matching pipe grade to SA387 Grade 11, used for moderate temperature steam and process lines where plain carbon steel loses strength and oxidation resistance.

1Cr-0.5Mo seamless pipe. The economical Cr-Mo pipe grade for boiler feed, steam and hot process service up to around 540 C, and the usual partner to SA387 Grade 12 plate.

2.25Cr-1Mo seamless pipe — the main steam and hot reheat standard. P22 carries creep strength and hydrogen resistance across refinery hot wall piping, superheater headers and heater coils, and is the pipe most often paired with SA387 Grade 22 vessels.

5Cr-0.5Mo seamless pipe for sulphidic and naphthenic service. Specified on crude and vacuum transfer lines and heater passes where sulphur attack, not pressure, sets the material.

9Cr-1Mo seamless pipe. Higher chromium for oxidation and sulphidic corrosion resistance in refinery heater coils and high temperature transfer lines.

Modified 9Cr-1Mo-V (P91) seamless pipe for supercritical steam. The creep strength allows a much thinner wall than P22 at 580 - 600 C, cutting weight and thermal fatigue on main steam and hot reheat lines. Hardness after PWHT is reported on every length.

Normalised structural plate with guaranteed 27 J impact energy at -20 C. The J2+N condition gives consistent toughness and flatness through thick sections, which is why it is specified for welded structures, crane and bridge work and heavy fabrication in the Gulf.

Carbon pressure vessel plate for moderate and lower temperature service. The lower carbon of Grade 60 gives better formability and weldability than Grade 70, which suits cold-formed heads, thin shells and plant where notch toughness matters more than tensile strength.

The default carbon pressure vessel plate. Grade 70 carries the highest tensile of the SA516 family, and for sour service it is supplied with controlled sulphur, calcium treatment and HIC / SSC testing so wet H2S equipment can be built from a qualified plate rather than an upgrade alloy.

The default seawater alloy. 90% copper with 10% nickel and a controlled iron addition builds a protective cuprous oxide film in seawater, and the inherent copper toxicity stops macrofouling — barnacles and mussels do not settle, so cooling lines stay clean without chlorination. Specified for ship and platform seawater systems, firewater ring mains and condenser tubing where the velocity stays below about 3.5 m/s.

The higher-duty cupro nickel. Tripling the nickel to 30% raises strength, erosion-corrosion resistance and the allowable seawater velocity to around 4.5 m/s, and lifts the service temperature well above 90/10. It is the grade for pump and valve-adjacent piping, hot brine and MSF desalination heat recovery, and any line where turbulence or sand loading would strip the film off 90/10.

الدرجة الدوبلكس الأكثر استخدامًا. يقارب ضعف قوة الخضوع للـ 316L، مما يسمح بأقسام أرق وأخف وزنًا مع توفير مقاومة أفضل بكثير للتآكل الناتج عن إجهاد الكلوريد.

فائق الدوبلكس مع PREN أعلى من 40 لأشد بيئات مياه البحر والخدمات الحامضية. يضيف S32760 (Zeron 100) التنغستن والنحاس لتعزيز مقاومة الأحماض.

سبائك النيكل-الكروم-الموليبدينوم معززة بالنيوبوميوم. قوة استثنائية ومقاومة للتآكل من درجات الحرارة منخفضة جدًا إلى 980 م دون معالجة حرارية.

سبيكة من النيكل والنحاس تتمتع بمقاومة فائقة لمياه البحر المتدفقة، وحمض الهيدروفلوريك والقلويات، ومناعة تامة ضد تآكل شروخ الكلوريد.

Nickel-iron-chromium with molybdenum, copper and titanium. The combination handles both reducing and oxidising acids and resists chloride stress corrosion cracking and sour well fluids, making 825 the standard CRA for sour service tubulars, cladding and acid plant.

The baseline transmission grade. X52 balances weldability against pressure rating, which is why it remains the default for gathering lines, utility piping and plant interconnects where wall thickness rather than yield strength drives the design.

The workhorse offshore and high-pressure grade. The higher yield allows a thinner wall at the same design pressure, cutting pipe weight on risers and long tie-backs, and X65 is the grade most often specified with sour service and HIC testing.

High strength thermomechanically rolled line pipe for long distance, large diameter transmission. X70 is specified where the pipeline economics are driven by wall thickness and steel tonnage over hundreds of kilometres.

فولاذ مقاوم للصدأ أوستنيتي يحتوي على الموليبدينوم. إضافة 2-3% من الموليبدينوم تُحسن مقاومة التنقر في الوسائط المحتوية على الكلوريد، مما يجعل 316L الدرجة الأساسية للخدمة البحرية والكيميائية في الخليج.

Titanium-stabilised 316. The titanium ties up carbon so the steel keeps its intergranular corrosion resistance after long exposure in the 425 - 815 C sensitisation range, and it holds higher creep strength than 316L in hot service.

سبائك التيتانيوم الأكثر استخدامًا، تشكل الغالبية العظمى من استهلاك التيتانيوم. ما يقرب من ثلاثة أضعاف قوة التيتانيوم النقي التجاري عند نفس الكثافة.