What sizes of SA516 Grade 60 Plates do you stock in Dubai?

We hold SA516 Grade 60 Plates in the following forms and size ranges — Plates: 5 - 200 mm thk, up to 3000 mm wide, cut to size. Cut-to-size, profiling and kitting are available on request, and anything outside the stock range is sourced direct from the mill.

What are the equivalent grades to SA516 Grade 60 Plates?

SA516 Grade 60 Plates is commonly cross-referenced with SA516 Gr 60, P265GH, 1.0425, SA516M Gr 415. Equivalents are nominal: send us the property that matters for your application and we will confirm the closest grade we can certify.

Is SA516 Grade 60 Plates supplied with mill certification?

Yes. Every delivery of SA516 Grade 60 Plates is supplied against ASTM A516 / ASME SA516, ASME Section VIII Div 1, ASTM A20 general requirements, ASTM A578 (ultrasonic examination), EN 10204 3.1 / 3.2 with EN 10204 3.1 mill certification and full heat-number traceability. Third-party inspection can be arranged on request.

What is SA516 Grade 60 Plates typically used for?

SA516 Grade 60 Plates is specified for pressure vessel shells and heads, storage tanks and separators, boiler drums and steam plant, mainly in Oil & Gas, Petrochemical, Power Generation. Tell us the duty and we will advise whether SA516 Grade 60 Plates or another carbon steel plates grade is the better fit.

SA516 Grade 60 Plates

ASTM / ASME A516 / SA516 Grade 60EN P265GH / 1.0425 (nearest)Metric SA516M Grade 415

حالة المخزونMill indent

مدة التوريد4 - 8 weeks mill indent

Carbon pressure vessel plate for moderate and lower temperature service. The lower carbon of Grade 60 gives better formability and weldability than Grade 70, which suits cold-formed heads, thin shells and plant where notch toughness matters more than tensile strength.

Better formability than Grade 70 for cold-formed heads
Normalised, impact tested and simulated PWHT options
Dual certification, NACE MR0103 / MR0175 and HIC / SSC testing available
Ultrasonic examination to SA578 and Z-direction testing on request

الأشكال والمقاسات المتوفرة

الشكل	نطاق المقاسات
الألواح	5 - 200 mm thk, up to 3000 mm wide, cut to size

التركيب الكيميائي (%)

العنصر	الحد الأدنى	الحد الأقصى
C	-	0.23 (t <= 25 mm)
Mn	0.60	1.20
Si	0.15	0.40
P	-	0.025
S	-	0.025

الخصائص الميكانيكية

الخاصية	القيمة	الوحدة
Yield Strength	220 min	MPa
Tensile Strength	415 - 550	MPa
Elongation	21 min (200 mm gauge)	%
Condition	As rolled or normalised	-

الخصائص الفيزيائية

الخاصية	القيمة	الوحدة
Density	7.85	g/cm3
Max Service Temperature	425	C

التطبيقات النموذجية

Pressure vessel shells and heads

Storage tanks and separators

Boiler drums and steam plant

Heat exchanger shells and tube sheets

أسئلة متكررة

[ 02 ] درجات أخرى في Carbon Steel Plates

S355J2+N Steel Plates

Ex-stock Dubai

EN S355J2+N / 1.0570ASTM A572 Gr 50 (nearest)

Normalised structural plate with guaranteed 27 J impact energy at -20 C. The J2+N condition gives consistent toughness and flatness through thick sections, which is why it is specified for welded structures, crane and bridge work and heavy fabrication in the Gulf.

2 شكل متوفر

S355J2W+N / Corten Steel Plates

Mill indent

EN S355J2W+N / 1.8965ASTM A588 Grade A / A709 Gr 50W

Weathering structural plate. Copper, chromium and nickel additions let a dense, adherent oxide patina form that seals the surface, so the structure can be left unpainted and the maintenance coating cycle disappears.

2 شكل متوفر

SA516 Grade 70 Plates

Ex-stock Dubai

ASTM / ASME A516 / SA516 Grade 70EN P355GH / 1.0473 (nearest)

The default carbon pressure vessel plate. Grade 70 carries the highest tensile of the SA516 family, and for sour service it is supplied with controlled sulphur, calcium treatment and HIC / SSC testing so wet H2S equipment can be built from a qualified plate rather than an upgrade alloy.

1 شكل متوفر

تحميل البيانات الفنية EN